Find my businessStart

Best restaurant thermometer for food safety: which kind to buy for which check

The best restaurant thermometer is a digital instant-read probe with a thin tip, accurate to within 2°F, that you can calibrate yourself. It reads food in a few seconds, fits a thin burger patty, and gives you a number to write on the log. A kitchen also needs a plain thermometer inside each fridge, and most kitchens add a second probe so one is always on the line.

This guide is for owners and managers who have to buy one this week. If the logs and the plan are the part you want done, find your restaurant and see your plan, built from your menu.

Want the log that goes with the probe? See your plan, built from your menu. No card.

What the rules ask of a restaurant thermometer

The FDA Food Code, which most states base their rules on, sets two things for the device itself [1]:

Rules differ by county. Ask your health department which accuracy and which types it expects before you buy; the Food Code is the starting point, not the last word.

The five kinds of restaurant thermometer

KindGood forNot good forSpeed
Digital instant-read probe (thermistor)All daily food checks: receiving, cooking, hot and cold holding, coolingLeaving in food in an ovenA few seconds
Thermocouple probeThin food, fast line checks, very small spotsNothing, except that it costs more and some need a battery change oftenOften the fastest
Dial stem thermometerA cheap backup, or a thermometer that stays in a stockpotThin food. A dial senses along the lower inch or two of the stem, not the tipSlow, often 15 to 20 seconds
Infrared (point-and-shoot) gunA quick scan of a delivery box, a shelf or a cooler wallThe inside of food. It reads the surface onlyInstant
Fridge and freezer air thermometerThe required reading in each cold unitFood temperatureSlow by design

Speeds are typical; the spec sheet of a given model has its own number. A Bluetooth thermometer is one of these kinds with a phone link added, so everything in the table applies to it too.

Which thermometer for which check

You do not need one device for everything. You need the right one for each job on the temperature log:

What to look for when you buy

Skip the brand wars. Compare models on these points, in this order:

  1. Stated accuracy. Look for ±1°F to ±2°F across the range you use, 0°F to 220°F is plenty. If a listing gives no accuracy at all, pass.
  2. Probe thickness and length. A thin tip, about the width of a pen refill, reads a patty or a fish fillet. A probe that is too short makes you lean over a hot pan.
  3. Response time. Under 5 seconds is common for a good digital probe. Slower means standing at the pan, which is a reason people skip the check.
  4. Can you calibrate it? Some models have a button or a screw to reset the ice point. The ones you cannot adjust must be replaced when they drift. Either way, you need to be able to test them. See the thermometer calibration log.
  5. Water resistance and a sleeve. A kitchen is wet and greasy. An IP-rated body that can be washed saves replacements.
  6. A readable display. Big digits, a backlight, and a lock or hold button. You will read it in a dim walk-in with gloves on.
  7. Battery type and life. A coin cell you can buy anywhere beats a custom pack.
  8. A foldable or cased probe. A bare tip in an apron pocket jabs people. A sleeve or fold-away blade is a safety feature.

Price is the last point, not the first. Instant-read probes are sold across a wide range; vendors change their prices, so read the current listing. An honest rule: a probe that costs a little more and that people actually use beats a cheap one nobody trusts.

How many do you need?

Buy by station, not by kitchen. A common set for a small restaurant:

A food truck can run on one probe and a spare. A restaurant with three stations and a walk-in usually needs three probes. If staff have to hunt for the probe, the log goes unfilled.

Calibrate the best restaurant thermometer you can buy, anyway

Even a good probe drifts, especially after a drop or a trip through the dish machine. A one-minute ice-point test tells you whether it still reads true [2]:

  1. Fill a cup to the top with crushed ice, then add clean water until the ice floats.
  2. Stir and wait a minute.
  3. Put the probe in so the tip is in the slush but not touching the cup, and wait for the number to settle.
  4. It should read 32°F, give or take the device's accuracy. If it is off by more than 2°F, adjust it if the model allows, or retire it.

Do this when the probe is new, after any drop, and on a schedule: weekly is a common habit for the line probe, monthly for a spare. The boiling-water check works too, but the boiling point depends on altitude, so ice is the easier one. Write each test on the calibration log with the date, the reading and your initials.

Using it correctly

Common mistakes

Do you need Bluetooth or a monitoring system?

Not to meet the rule. A plain probe plus a paper or phone log is a full record, and many small kitchens run on it. A Bluetooth probe adds an automatic time stamp; a wireless sensor in each cold unit adds an alert at 2 a.m. when a compressor fails. See restaurant temperature monitoring systems for when that pays and paper vs digital temperature logs for what an inspector accepts.

Questions

What is the best restaurant thermometer for checking food?

A digital instant-read probe with a thin tip and a stated accuracy of ±2°F or better. It is fast enough to use every time and thin enough for patties and fillets.

Is an infrared thermometer OK for HACCP logs?

Not for the inside of food, since it reads only the surface. It is useful for scanning a delivery or a cooler wall, and the probe reading is what you log.

How accurate does a restaurant thermometer have to be?

The Food Code asks for ±2°F (±1°C) on a food probe. Local codes can differ, so check yours.

How often should I calibrate it?

When it is new, after a drop, and on a routine: weekly for the main line probe is a common choice. Log each test.

Do I need a thermometer in the fridge if I use a probe?

Yes. Each refrigerated unit needs its own thermometer so staff can see the air temperature without opening the door [1].

Can I use a meat thermometer from a kitchen shop?

If it is accurate, thin and calibratable, yes. Many home dial meat thermometers are not, and an inspector may not accept one.

Ready to log with the one you buy? See your plan, built from your menu, with the log for the item your inspector cited.

Sources

  1. FDA Food Code 2022: food temperature measuring devices, accuracy, small-diameter probes, and cooking and holding temperatures. https://www.fda.gov/food/retail-food-protection/fda-food-code
  2. USDA Food Safety and Inspection Service, Kitchen thermometers (calibration by the ice-water method). https://www.fsis.usda.gov/food-safety/safe-food-handling-and-preparation/food-safety-basics/kitchen-thermometers

See also: refrigerator temperature log, walk-in cooler temperature log.

Seen "HACCP approved" on a box? What the label means.

Related: Infrared vs probe thermometer for a restaurant.

All food safety guides